English 中文 Español Português Français العربية Skip to content Home / Add concentration after the juice or puree decision Technical note
Add concentration after the juice or puree decision An evaporation module changes product flow, utilities and cleaning without changing the base extraction route.
Keep extraction separate Juice extraction removes a liquid from tissue; puree processing retains a controlled tissue fraction. Concentration removes water from the chosen product downstream. A request for concentrate still needs to say whether the feed is juice or puree and define the solids measurement.
Evaluate the difficult end condition As concentration proceeds, flow behaviour, deposits and heat transfer can change. A system suitable for a relatively fluid juice cannot automatically be specified for a fibrous puree. Request sample work at the proposed final condition, not just a test of dilute feed.
Connect the whole scope The feed tank, evaporator, vapour system, concentrate pump and subsequent treatment/filling must be sized together. Record thermal exposure and product quality limits. Concentration alone is not a preservation claim or a guarantee of ambient storage.
Bring to the project review Juice or puree feed specification Initial/final solids with measurement method Viscosity and fouling trial evidence Steam, cooling, vacuum and downstream scope Discuss these conditions ↗ Equipment affected by this decision Optional concentration module Juice or puree with known solids and flow behaviour → Concentrated product and separated water vapour/condensate
Configuration and equipment drawing follow the confirmed process scope. Downstream option
Increase the agreed solids level after the base juice or puree route has been established.
In Juice or puree with known solids and flow behaviour Out Concentrated product and separated water vapour/condensate Product buffer and transfer system Juice or puree at a measured process condition → Controlled feed to concentration, treatment or an existing process
Configuration and equipment drawing follow the confirmed process scope. Downstream interface
Keep the correct product branch moving without losing its capacity and hygiene boundaries.
In Juice or puree at a measured process condition Out Controlled feed to concentration, treatment or an existing process Equipment presentation Validated finishing scope
Provide the heating, holding and cooling interfaces required by the qualified process design.
In Defined juice or puree formulation at specified feed conditions Out Product meeting the validated process condition for the package route General process and safety references: sources and evidence . Operating conditions require the actual product and qualified process review.
Multi-stage root washing system Raw-root input, kg/h and lot size Soil condition and root dimensions Make-up water, screening and wastewater basis Discharge height and carryover water Compare machine arrangements with representative dry soil, sticky mud, broken roots and seasonal variation.
Read the complete equipment scope →
Enquire about this equipment
Stone separation module Stone size and density distribution Root buoyancy and size range Water flow and reject removal arrangement Inspection and isolation access Request a challenge trial using representative roots and identified foreign-material hazards.
Read the complete equipment scope →
Enquire about this equipment
Root inspection conveyor Belt loading and product layer Inspection staffing or detection method Reject location and collection Conveyor speed and washdown access Define unacceptable defects and foreign material before comparing throughput.
Read the complete equipment scope →
Enquire about this equipment
Optional root peeling module Peel acceptance criterion Root shape and seasonal variation Measured peel loss and water demand Cleaning and wear-component access Compare peeled and unpeeled sample products against the actual customer specification.
Read the complete equipment scope →
Enquire about this equipment
Carrot cutting and size reduction Incoming root dimensions Required cut distribution or mash condition Product temperature and feed continuity Knife access and foreign-material protection Run extraction trials with the proposed particle size and record the resulting product and side stream.
Read the complete equipment scope →
Enquire about this equipment
Optional conditioning / softening unit Purpose of conditioning and trial evidence Residence-time distribution and product temperature Heating medium and dilution impact Drain-down and startup handling Compare the product, energy demand and extraction behaviour with and without the proposed conditioning step.
Read the complete equipment scope →
Enquire about this equipment
Carrot juice extraction press Mash particle size and temperature Liquid quality and solids target Feed rate on prepared-mash basis Residue moisture, cleaning and collection Measure juice, residue and cleaning losses using the same batch boundary before comparing offers.
Read the complete equipment scope →
Enquire about this equipment
Juice solids separation / finishing Incoming solids and particle distribution Desired cloud and sediment behaviour Feed temperature and viscosity Side-stream quantity and cleaning cycle Use retained product samples and an agreed test method for suspended solids or sedimentation.
Read the complete equipment scope →
Enquire about this equipment
Carrot pulping machine Prepared-feed dimensions and softness Screen configuration and speed basis Pulp temperature and fibre condition Reject handling and accessible wear parts Compare pulp texture, coarse rejection and downstream refining duty on the same representative feed.
Read the complete equipment scope →
Enquire about this equipment
Puree refining and texture control Retained reference sample or particle criterion Screen choice and product temperature Pressure, throughput and screen loading Reject balance and wear limits Evaluate the cooled product as well as the processing-temperature sample using the agreed method.
Read the complete equipment scope →
Enquire about this equipment
Product buffer and transfer system Product viscosity at a stated temperature and method Flow range, pressure and available inlet condition Buffer working volume and residence time Drainability, seals and cleaning return Use measured product behaviour and a pressure-drop assessment at the limiting process condition.
Read the complete equipment scope →
Enquire about this equipment
Optional concentration module Initial and target soluble/total solids with method Feed and discharge viscosity Residence time and quality limits Steam, vacuum, cooling and condensate interfaces Trial the product through the intended solids range; do not extrapolate juice evaporator performance to puree.
Read the complete equipment scope →
Enquire about this equipment
Product-specific thermal treatment Product formulation, acidity and rheology Validated process requirement and flow envelope Heating/holding/cooling instrumentation Fouling, differential pressure and utilities Resolve the process and package responsibility before promising shelf stability or ordering a heating skid.
Read the complete equipment scope →
Enquire about this equipment
Product and package filling interface Package format, fitment and fill weight Product temperature, viscosity and particles Throughput expressed as packages and product mass Cleaning, sterilization and closure requirements Confirm actual package compatibility and filling trials before specifying a model.
Read the complete equipment scope →
Enquire about this equipment
Cleaning and drain-down system Circuit inventory and manual-clean boundaries Product deposits and worst-case soil Cleaning return, drainage and utilities Verification points and safe isolation Map each equipment item to a cleaning circuit or accessible manual task and prove the end-of-run condition.
Read the complete equipment scope →
Enquire about this equipment
