English 中文 Español Português Français العربية Skip to content Home / Carrot Processing Line Capacity Buying guide
Carrot Processing Line Capacity Prepare a comparable carrot line capacity enquiry using the correct weighing point, product route, operating time and measured mass balance.
Name the stream beside the capacity Raw-root intake, prepared feed and finished product are three different measurements. Soil, unsuitable roots, peel, fibre and other rejects can leave the process between them. Concentration removes additional water downstream. Put the stream name beside every hourly or batch rate so equipment proposals do not compare different parts of the process as though they were the same.
Allow for the operating pattern Describe available operating hours, lot changes, cleaning periods and upstream feed continuity. Buffer requirements depend on those conditions as well as the nominal rate. Establish whether the project needs continuous production, batch handling or a combination. Startup and shutdown material should be measured explicitly rather than silently counted as steady-state finished output.
Use trials to support the balance Compare root input, product output, side streams and retained material over the same period. Identify any ingredients or water added to the process and use the specified solids measurement for concentration calculations. The resulting balance supports equipment selection; it is more reliable than quoting a universal carrot yield without feed, preparation and product conditions.
Process references and image information →
Equipment presentation Common preparation
Remove heavy soil through pre-washing, brush washing and a clean-water final rinse before inspection and cutting.
In Raw roots with soil and adhering debris Out Washed roots with accessible surfaces for inspection Carrot juice extraction press Prepared root mash suitable for pressing → Extracted liquid and a fibre-rich press residue
Configuration and equipment drawing follow the confirmed process scope. Juice branch
Separate a liquid stream from prepared carrot tissue while maintaining a measurable side-stream balance.
In Prepared root mash suitable for pressing Out Extracted liquid and a fibre-rich press residue Equipment presentation Puree branch
Break down prepared roots into a pumpable pulp while separating material unsuitable for the target product.
In Cut or conditioned roots suitable for pulping Out Pulp containing comminuted tissue plus a coarse reject stream Optional concentration module Juice or puree with known solids and flow behaviour → Concentrated product and separated water vapour/condensate
Configuration and equipment drawing follow the confirmed process scope. Downstream option
Increase the agreed solids level after the base juice or puree route has been established.
In Juice or puree with known solids and flow behaviour Out Concentrated product and separated water vapour/condensate Equipment presentation Validated finishing scope
Bring product delivery, container handling and closure into one specified interface.
In Prepared product and a compatible package under a defined process Out Filled, closed units transferred to the agreed distribution route Project enquiry
Turn your product brief into an equipment scope Start with the product, raw material and production basis.
Discuss your project ↗ Before you enquire
Questions worth answering. Clear product and equipment requirements make the next conversation useful.
Which equipment duties are relevant to this project? Multi-stage root washing system; Carrot juice extraction press; Carrot pulping machine; Optional concentration module; Product and package filling interface. The final scope follows the product, trials and selected package.
What should I send with my enquiry? Capacity with its weighing point; Juice, puree or concentrate route; Operating hours and cleaning schedule; Representative lot and trial balance; Package size and finished-product demand. If a condition is undecided, describe the intended finished product.
Multi-stage root washing system Raw-root input, kg/h and lot size Soil condition and root dimensions Make-up water, screening and wastewater basis Discharge height and carryover water Compare machine arrangements with representative dry soil, sticky mud, broken roots and seasonal variation.
Read the complete equipment scope →
Enquire about this equipment
Stone separation module Stone size and density distribution Root buoyancy and size range Water flow and reject removal arrangement Inspection and isolation access Request a challenge trial using representative roots and identified foreign-material hazards.
Read the complete equipment scope →
Enquire about this equipment
Root inspection conveyor Belt loading and product layer Inspection staffing or detection method Reject location and collection Conveyor speed and washdown access Define unacceptable defects and foreign material before comparing throughput.
Read the complete equipment scope →
Enquire about this equipment
Optional root peeling module Peel acceptance criterion Root shape and seasonal variation Measured peel loss and water demand Cleaning and wear-component access Compare peeled and unpeeled sample products against the actual customer specification.
Read the complete equipment scope →
Enquire about this equipment
Carrot cutting and size reduction Incoming root dimensions Required cut distribution or mash condition Product temperature and feed continuity Knife access and foreign-material protection Run extraction trials with the proposed particle size and record the resulting product and side stream.
Read the complete equipment scope →
Enquire about this equipment
Optional conditioning / softening unit Purpose of conditioning and trial evidence Residence-time distribution and product temperature Heating medium and dilution impact Drain-down and startup handling Compare the product, energy demand and extraction behaviour with and without the proposed conditioning step.
Read the complete equipment scope →
Enquire about this equipment
Carrot juice extraction press Mash particle size and temperature Liquid quality and solids target Feed rate on prepared-mash basis Residue moisture, cleaning and collection Measure juice, residue and cleaning losses using the same batch boundary before comparing offers.
Read the complete equipment scope →
Enquire about this equipment
Juice solids separation / finishing Incoming solids and particle distribution Desired cloud and sediment behaviour Feed temperature and viscosity Side-stream quantity and cleaning cycle Use retained product samples and an agreed test method for suspended solids or sedimentation.
Read the complete equipment scope →
Enquire about this equipment
Carrot pulping machine Prepared-feed dimensions and softness Screen configuration and speed basis Pulp temperature and fibre condition Reject handling and accessible wear parts Compare pulp texture, coarse rejection and downstream refining duty on the same representative feed.
Read the complete equipment scope →
Enquire about this equipment
Puree refining and texture control Retained reference sample or particle criterion Screen choice and product temperature Pressure, throughput and screen loading Reject balance and wear limits Evaluate the cooled product as well as the processing-temperature sample using the agreed method.
Read the complete equipment scope →
Enquire about this equipment
Product buffer and transfer system Product viscosity at a stated temperature and method Flow range, pressure and available inlet condition Buffer working volume and residence time Drainability, seals and cleaning return Use measured product behaviour and a pressure-drop assessment at the limiting process condition.
Read the complete equipment scope →
Enquire about this equipment
Optional concentration module Initial and target soluble/total solids with method Feed and discharge viscosity Residence time and quality limits Steam, vacuum, cooling and condensate interfaces Trial the product through the intended solids range; do not extrapolate juice evaporator performance to puree.
Read the complete equipment scope →
Enquire about this equipment
Product-specific thermal treatment Product formulation, acidity and rheology Validated process requirement and flow envelope Heating/holding/cooling instrumentation Fouling, differential pressure and utilities Resolve the process and package responsibility before promising shelf stability or ordering a heating skid.
Read the complete equipment scope →
Enquire about this equipment
Product and package filling interface Package format, fitment and fill weight Product temperature, viscosity and particles Throughput expressed as packages and product mass Cleaning, sterilization and closure requirements Confirm actual package compatibility and filling trials before specifying a model.
Read the complete equipment scope →
Enquire about this equipment
Cleaning and drain-down system Circuit inventory and manual-clean boundaries Product deposits and worst-case soil Cleaning return, drainage and utilities Verification points and safe isolation Map each equipment item to a cleaning circuit or accessible manual task and prove the end-of-run condition.
Read the complete equipment scope →
Enquire about this equipment
