Tropical Purée Fruit / processing line
Mango Processing Line
Depicted route: Mango pulp
Mango flesh recovery is linked to stone size, peel separation, ripeness and fibre character. The useful specification defines the accepted flesh and the desired purée, rather than treating every kilogram leaving a destoner as finished product. Sort for processing maturity, wash and separate peel and stone from the edible flesh. Refine the recovered pulp to remove coarse fibres and unwanted peel fragments. Assess the resulting viscosity before selecting transfer and concentration equipment; ripe purée and formulated nectar are different product specifications.
Raw material and product boundary
Product directions
- single-strength purée
- purée concentrate
- nectar base
Incoming material considerations
- What stone size, flesh attachment and fibre level occur in the intended mango varieties, including early and late harvest lots?
- How smooth must the purée be, what speck level is acceptable, and is concentration required or would single-strength bulk purée suit the buyer?
- Define incoming state, variety, maturity, accepted defects and supply interruptions in the purchasing brief. A proposed line should be demonstrated with representative commercial lots rather than a single ideal sample.
Process flow: preparation to product
- 01
Receive and grade
Equipment duty: Inspection conveyor and fruit grader
Identify variety, maturity and accepted fruit dimensions.
Include the stone and fibre behaviour of the purchased varieties in the trial plan.
- 02
Wash and inspect
Equipment duty: Washer, rinse elevator and brushing where justified
Clean the fruit before the flesh-separation section.
Keep rejected fruit and dirty wash water outside the prepared-flesh circuit.
- 03
Separate peel and stone
Equipment duty: Mango-compatible destoner and peeling arrangement
Recover edible flesh while excluding coarse skin and the hard stone.
Inspect skin specks, fragments and flesh retained with the stone stream separately.
- 04
Refine the flesh
Equipment duty: Pulper-refiner
Develop the desired fibre and particle character.
Assess the product against its intended nectar, purée or fruit-base use rather than a single visual smoothness standard.
- 05
Review optional conditioning
Equipment duty: Defined conditioning interface and sample points
Evaluate any proposed change in preparation or intermediate handling.
A preheating or further-separation step needs its own purpose and product trial, not a universal setting borrowed from another fruit.
- 06
Route natural or concentrated product
Equipment duty: Covered tank and suitable transfer pump
Supply the chosen single-strength or concentrated-purée route.
Evaporation, deaeration and aroma handling are separately specified options with their own inlet requirements.
- 07
Specify preservation around the actual product
Equipment duty: Selected treatment unit, controlled transfer and process instruments
Confirm the measured product composition, particulate load and intended storage chain before the treatment and filling arrangement is selected.
The peeled and destoned purée route needs its own validated process. A drawing, a heat-exchanger name or a successful extraction trial does not establish a safe treatment schedule or a finished shelf-life claim.
- 08
Fill, identify and verify the packed ingredient
Equipment duty: Compatible filler, packaging interface and lot-identification station
Match the approved ingredient to the selected package and handling conditions. Record the production lot and the conditions required by its defined distribution route.
The filling boundary belongs in the project specification: container format, product-contact interface, filling hygiene, storage and the downstream user’s receiving requirements must agree before commercial acceptance.
Equipment composition and selection
Inspection conveyor and fruit grader
Control the incoming-material presentation before preparation.
Selection basis: Check actual lot condition, peak arrivals and the accepted size range. Provide a sample/reject point that can be operated without obstructing feed to the next machine.
Mango-compatible destoner and peeling arrangement
Peel, seed and fibre separation.
Selection basis: Preparation should be evaluated using the actual variety and ripeness range. A visually smooth sample does not by itself demonstrate controlled coarse particles, acceptable fibre or stable transfer.
Pulper-refiner
Create the agreed intermediate condition for downstream equipment.
Selection basis: Agree an acceptance sample, a measurable particle or separation target and a reject-handling method. Select contact parts and access arrangements after trials with representative material.
Product buffer and transfer system
Connect preparation, treatment and filling without assuming all sections run at the same rate.
Selection basis: Record viscosity, particle character, temperature envelope and expected stoppages. Confirm drainability, sampling points and how unaccepted or interrupted product is identified and handled.
Preservation, packaging and cleaning interfaces
Complete the declared process boundary.
Selection basis: The quoted scope should identify included instruments, services, containers, hygienic connections and validation responsibilities. An item list without these interfaces is not a complete line specification.
Quality, cleaning and separate streams
Quality observations
- Check skin specks, hard fragments, fibre, colour and consistency on identified varieties. Compare samples after the same downstream handling.
- Define the sampling location, sample preparation, measurement method and acceptable variation. Retain traceable comparisons through the intended downstream route; a favourable immediate sample is not proof of storage stability.
Separate material streams
- Separate peel, stones and fibrous rejects from the edible purée. Any secondary flesh recovery must retain fragment and skin controls.
Cleaning and changeover
- Fibres and flesh can remain around screens, stone discharge and pump contact parts. Include access and a product-specific residue-removal assessment.
- Assign cleaning responsibilities to the open preparation zone and the closed product circuit separately. Confirm which parts require removal or inspection and how cleaning effectiveness will be demonstrated with the actual product soil.
Mango and carrot processing
Where this route differs from the site's primary line
Carrot projects begin with soil removal and divide into juice, puree and concentrated products. Use that same measurement discipline for this material: distinguish received raw material, prepared feed, recovered product and separate residue streams. The process below highlights the material-specific front end before any downstream equipment scope is discussed.
Tropical purées share carrot purée transfer questions but substitute peels, stones and variable ripeness for the root front end. Product texture and coarse-fibre rejection set the finishing target.
Packaging and storage interfaces
Specify whether the peeled and destoned purée is supplied as a chilled, frozen, otherwise treated or aseptically handled ingredient, as applicable to the developed product. Package material, closure, fill conditions and distribution are a connected system. Any claimed ambient stability or shelf life requires product- and package-specific validation; the process introduction does not set treatment temperatures or holding times.
Information for an engineering brief
- Trial accepted mango varieties and maturity extremes, measuring product quality and flesh retained with rejects together.
- Provide the intended finished-product specification, representative raw-material samples, daily operating pattern and seasonal peak load.
- Identify available utilities, factory layout, drainage, reject collection and the exact inlet/outlet conditions of equipment supplied by others.
- Agree trial acceptance criteria and define the preservation, filling, cleaning and commissioning responsibilities before finalising the equipment scope.
Technical reading and related materials
Define the line around your material
Include the incoming form, product target, quantity and measurement basis, package and known site interfaces in your enquiry. Describe this material explicitly in the project goal.
Prepare a project enquiry →