English 中文 Español Português Français العربية Skip to content Home / Carrot Processing CIP System Whole-line interface
Cleaning and drain-down system Make every preparation, extraction and finishing circuit accessible to its appropriate cleaning method.
Incoming material The defined dirty equipment circuits after product recovery Outgoing material Cleaned equipment assessed under the agreed verification programme Working arrangement CIP circuits, manual cleaning tasks, return paths and product recovery must be separated by hygienic function. A central skid cannot compensate for inaccessible machinery.
Cleaning and drain-down system The defined dirty equipment circuits after product recovery → Cleaned equipment assessed under the agreed verification programme
Configuration and equipment drawing follow the confirmed process scope. Specification
Define these parameters Circuit inventory and manual-clean boundaries Product deposits and worst-case soil Cleaning return, drainage and utilities Verification points and safe isolation Map each equipment item to a cleaning circuit or accessible manual task and prove the end-of-run condition.
Open parameter panel ↗ Integration
Connect the interfaces Separate root-washing wastewater from product-area cleaning. Coordinate return capacity, chemical handling and equipment readiness.
Cleaning and access Inspect the cleaning system itself, including tanks, return strainers, dead ends and drains. Procedures require site-specific validation.
There is no universal chemical strength, temperature or time schedule for all carrot line materials and soils.
Connected equipment Equipment presentation Common preparation
Remove heavy soil through pre-washing, brush washing and a clean-water final rinse before inspection and cutting.
In Raw roots with soil and adhering debris Out Washed roots with accessible surfaces for inspection Carrot juice extraction press Prepared root mash suitable for pressing → Extracted liquid and a fibre-rich press residue
Configuration and equipment drawing follow the confirmed process scope. Juice branch
Separate a liquid stream from prepared carrot tissue while maintaining a measurable side-stream balance.
In Prepared root mash suitable for pressing Out Extracted liquid and a fibre-rich press residue Equipment presentation Puree branch
Break down prepared roots into a pumpable pulp while separating material unsuitable for the target product.
In Cut or conditioned roots suitable for pulping Out Pulp containing comminuted tissue plus a coarse reject stream Project enquiry
Discuss this equipment in your line Start with the product, raw material and production basis.
Discuss your project ↗ Before you enquire
Questions worth answering. Clear product and equipment requirements make the next conversation useful.
What does the cleaning and drain-down system do? Make every preparation, extraction and finishing circuit accessible to its appropriate cleaning method.
How should this equipment be selected? Map each equipment item to a cleaning circuit or accessible manual task and prove the end-of-run condition.
What information should I include in the enquiry? Circuit inventory and manual-clean boundaries; Product deposits and worst-case soil; Cleaning return, drainage and utilities; Verification points and safe isolation. Include the upstream and downstream product interfaces.
Multi-stage root washing system Raw-root input, kg/h and lot size Soil condition and root dimensions Make-up water, screening and wastewater basis Discharge height and carryover water Compare machine arrangements with representative dry soil, sticky mud, broken roots and seasonal variation.
Read the complete equipment scope →
Enquire about this equipment
Stone separation module Stone size and density distribution Root buoyancy and size range Water flow and reject removal arrangement Inspection and isolation access Request a challenge trial using representative roots and identified foreign-material hazards.
Read the complete equipment scope →
Enquire about this equipment
Root inspection conveyor Belt loading and product layer Inspection staffing or detection method Reject location and collection Conveyor speed and washdown access Define unacceptable defects and foreign material before comparing throughput.
Read the complete equipment scope →
Enquire about this equipment
Optional root peeling module Peel acceptance criterion Root shape and seasonal variation Measured peel loss and water demand Cleaning and wear-component access Compare peeled and unpeeled sample products against the actual customer specification.
Read the complete equipment scope →
Enquire about this equipment
Carrot cutting and size reduction Incoming root dimensions Required cut distribution or mash condition Product temperature and feed continuity Knife access and foreign-material protection Run extraction trials with the proposed particle size and record the resulting product and side stream.
Read the complete equipment scope →
Enquire about this equipment
Optional conditioning / softening unit Purpose of conditioning and trial evidence Residence-time distribution and product temperature Heating medium and dilution impact Drain-down and startup handling Compare the product, energy demand and extraction behaviour with and without the proposed conditioning step.
Read the complete equipment scope →
Enquire about this equipment
Carrot juice extraction press Mash particle size and temperature Liquid quality and solids target Feed rate on prepared-mash basis Residue moisture, cleaning and collection Measure juice, residue and cleaning losses using the same batch boundary before comparing offers.
Read the complete equipment scope →
Enquire about this equipment
Juice solids separation / finishing Incoming solids and particle distribution Desired cloud and sediment behaviour Feed temperature and viscosity Side-stream quantity and cleaning cycle Use retained product samples and an agreed test method for suspended solids or sedimentation.
Read the complete equipment scope →
Enquire about this equipment
Carrot pulping machine Prepared-feed dimensions and softness Screen configuration and speed basis Pulp temperature and fibre condition Reject handling and accessible wear parts Compare pulp texture, coarse rejection and downstream refining duty on the same representative feed.
Read the complete equipment scope →
Enquire about this equipment
Puree refining and texture control Retained reference sample or particle criterion Screen choice and product temperature Pressure, throughput and screen loading Reject balance and wear limits Evaluate the cooled product as well as the processing-temperature sample using the agreed method.
Read the complete equipment scope →
Enquire about this equipment
Product buffer and transfer system Product viscosity at a stated temperature and method Flow range, pressure and available inlet condition Buffer working volume and residence time Drainability, seals and cleaning return Use measured product behaviour and a pressure-drop assessment at the limiting process condition.
Read the complete equipment scope →
Enquire about this equipment
Optional concentration module Initial and target soluble/total solids with method Feed and discharge viscosity Residence time and quality limits Steam, vacuum, cooling and condensate interfaces Trial the product through the intended solids range; do not extrapolate juice evaporator performance to puree.
Read the complete equipment scope →
Enquire about this equipment
Product-specific thermal treatment Product formulation, acidity and rheology Validated process requirement and flow envelope Heating/holding/cooling instrumentation Fouling, differential pressure and utilities Resolve the process and package responsibility before promising shelf stability or ordering a heating skid.
Read the complete equipment scope →
Enquire about this equipment
Product and package filling interface Package format, fitment and fill weight Product temperature, viscosity and particles Throughput expressed as packages and product mass Cleaning, sterilization and closure requirements Confirm actual package compatibility and filling trials before specifying a model.
Read the complete equipment scope →
Enquire about this equipment
Cleaning and drain-down system Circuit inventory and manual-clean boundaries Product deposits and worst-case soil Cleaning return, drainage and utilities Verification points and safe isolation Map each equipment item to a cleaning circuit or accessible manual task and prove the end-of-run condition.
Read the complete equipment scope →
Enquire about this equipment
Equipment presentation
Equipment presentation